Uncompromising quality
Uncompromising quality
Uncompromising quality
Uncompromising quality
Uncompromising quality
Uncompromising quality
chiusura Natalizia / Christmas closing: 20/12 hh 12:00 >> 06/01
AISI 4130 (SAE-AISI 4130)
CORRESPONDENCE TO INTERNATIONAL DESIGNATIONS
| QUALITY | EUROPE | GERMANY | FRANCE | SPAIN | G.B. | USA | |
|---|---|---|---|---|---|---|---|
| EN | DIN | W.n. | AFNOR | UNE | B.S. | AISI/SAE | |
| AISI 4130 | 25/30CrMo4 | 1.7218 | 708A25 | 4130 | |||
CHEMICAL ANALYSIS
| STEEL DESIGNATION | CHEMICAL ANALYSIS | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| SYMBOLIC | C | Mn | Si | P max |
S max |
Cr | Mo | V | Al max |
| AISI 4130 | 0,28 ÷ 0,33 | 0,40 ÷ 0,60 | 0,15 ÷ 0,35 | 0,035 | 0,040 | 0,60 ÷ 1,10 | 0,15 ÷ 0,25 | - | - |
MECHANICAL CHARACTERISTICS
| STEEL | d ≤ 16mm | 16mm < d ≤ 40mm | 40mm < d ≤ 100mm | 100mm < d ≤ 160mm | |||||||||||||
| SYMBOLIC | NUMERIC | Re min | Rm | A min | KCU min | Re min | Rm | A min | KCU min | Re min | Rm | A min | KCU min | Re min | Rm | A min | KCU min |
| N/mm2 | % | J | N/mm2 | % | J | N/mm2 | % | J | N/mm2 | % | J | ||||||
| AISI 4130 | 1,7218 | 685 | 880 ÷ 1080 |
12 | 32,5 | 635 | 830 ÷ 1030 |
12 | 32,5 | 520 | 740 ÷ 880 |
13 | 30 | 420 | 690 ÷ 830 |
15 | 30 |
JOMINY HARDENABILITY
| STEEL DESIGNATION | RANGE LIMITS | HRC HARDNESS MEASURED FROM THE QUENCHED END OF THE TEST TUBE (MM) | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| SYMBOLIC | NUMERIC | 1,5 | 3 | 5 | 7 | 9 | 11 | 13 | 15 | 20 | 25 | 30 | 35 | 40 | |
| AISI 4130 | 1.7218 | max | 56 | 55 | 53 | 51 | 49 | 47 | 45 | 42 | 39 |
37 |
35 | 33 | 32 |
| min | 46 | 45 | 42 | 38 | 35 | 30 | 28 | 26 | 24 | 23 | 21 | 20 | - | ||
USUALLY AVAILABLE EX STOCK
| M.T. COLORATION | QUALITY | HEAT TREATMENT | SURFACE | DIAMETER (mm) |
|---|---|---|---|---|
| AISI 4130 | Quenched and tempered | rolled | 80-350 |
 |
Download technical sheet |
Steels
Our steel always comes from the same European steelworks, which guarantee a continuity for what concerns quality. The constant quality of the supplies allows to have repetitive parameters in mechanical processing and a greater control over deformations during heat treatment.
Machining
Precise cuttings of small and big series are guaranteed by the employement of latest generation automatic saws that were projected and realized in order to guarantee precision standards required by customers, reducing processing wastage.
Quality
The certification and introduction of the Quality System management allowed M.T.Acciai to improve not only its efficiency, but also the quality that is offered, in order to better meet our customers’ needs.